Internet DRAFT - draft-anderson-gsmp-swpart-mib
draft-anderson-gsmp-swpart-mib
Internet Draft T. Anderson
Expiration: August 2001 Intel
File: draft-anderson-gsmp-swpart-mib-00.txt A. Doria
Nortel Networks
J. Yong
Telia
J. Sydir
B. Srinivasan
CPlane
February 22, 2001
Switch Partitioning MIB
Status of this Memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC2026. Internet-Drafts are
working documents of the Internet Engineering Task Force (IETF),
its areas, and its working groups. Note that other groups may
also distribute working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other
documents at any time. It is inappropriate to use Internet-Drafts
as reference material or to cite them other than as ``work in
progress.''
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
To view the current status of any Internet-Draft, please check the
``1id-abstracts.txt'' listing contained in an Internet-Drafts
Shadow Directory, see http://www.ietf.org/shadow.html.
1. Abstract
This document defines a Management Information Base (MIB) for
partitioning a single switch into a set of virtual switches (VSs).
The partitioning MIB defined here is largely based on [MSF-VSMIB].
2. Introduction
There are four logical interfaces for managing a switch that can be
divided up into multiple virtual switches. They are (1) the
interface to control the behavior of the switch as a whole, (2) the
interface to control the behavior of each virtual switch, (3) the
interface to query what resources exist on the switch, and (4) the
interface to create and delete virtual switches and to partition the
available resources amongst these virtual switches. Interfaces 1
Anderson et al.@ [Page 1]
Internet Draft IP Forwarding PIB July 2000
and 2 are likely to be very similar. MIBs currently exist for the
purpose of managing these non-virtualized parts of switches. These
interfaces are not considered further in this document. While the
latter two interfaces are clearly related, they perform different
functions - discovery and configuration respectively. The
motivation for separating these functions into different MIBs is
that in many cases other MIBs already support resource discovery.
The missing element is a MIB to support the virtual switch
partitioning function. Therefore, in this document, MIBs for
discovering switch resources are assumed to exist and we instead
focus on the MIB for the virtual switch partitioning function. This
partitioning function creates and deletes virtual switches on a
switch and assigns resources in the support of those virtual
switches.
3. Base Switch Resources
The following switch resources may be partitioned amongst virtual
switches.
3.1. Bandwidth, Buffer Space, and Queue Schedulers
The bandwidth, buffer space, and queue schedulers assigned to a VS
can be abstracted using a single parameter: the equivalent
bandwidth per port assigned to the VS in both the incoming and
outgoing directions. The equivalent bandwidth is associated with
a performance target. The performance target is most common in
the form of a loss target but also a delay target can be used.
3.2. Label Space
Label space resources are allocated independently for the incoming
and outgoing directions of switch ports. Label space must be
specified as a set of potentially non-contiguous ranges to allow
for the flexible allocation of label space in a dynamic
environment. Depending on what service a port provides the label
space can be of a different form, e.g., the label space is VPI/VCI
for an ATM port and DLCI for a frame relay port.
3.3. Routing Table Space
The abstraction for routing table space is more complex than that
for label space because different switches implement routing
tables of different granularities. Some switches implement a
routing table at each port, while others implement a common
routing table, which is shared by the connections that go through
all of the ports.
3.4. Control Link Bandwidth and Processor Cycles
When multiple VSs exercise control over separate LSPs, which are
hosted on the same physical switch, they potentially share the
processor on which the Switch Partitioning Functionality and
Anderson et al. Expires January 2001 [Page 2]
Internet Draft IP Forwarding PIB July 2000
Switch Control Functionality is executed. Multiple controllers may
also share a communication link to the switch.
4. The Partitioning MIB
--NOTE 1: How does one use this mib:
--
-- The manager can get information about the switch by doing the
-- usual gets on the variables
--
-- A) Creation of a virtual switch:
-- 1) To create a virtual switch create a new row by setting the
-- vSwitchTableRowStatus to 'createAndWait'
--
-- 2) Set the other variables as the configuration requires. NOTE
-- the only requisite information before proceeding to step 3
-- is the SCI information. This specifies
-- how the virtual switch communicates with the external
-- world.
--
-- 3) Commit the vSwitchTableRowStatus by setting it to 'active'
--
--
-- B) Deleting a virtual switch:
-- 1) Set the vSwitchTableRowStatus of the corresponding virtual
-- switch to 'destroy'
--
--
-- C) Changing virtual switch resources:
-- 1) Set the vSwitchTableRowStatus of the appropriate virtual
-- switch to 'notInService' (this is the convention used to
-- allow row variables to be modified, while not in operation).
--
-- 2) Add/Delete/Change the resources as necessary. This is done
-- by either creating/deleting/modifying rows in the virtual
-- port and vpi/vci range tables. Commit individual changes
-- by setting row status variables to active (unless the
-- change is a delete).
--
-- 3) Commit all changes by setting the vSwitchTableRowStatus to
-- 'active'
Partition-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, enterprises, Integer32,
Counter32, Gauge32, TimeTicks, IpAddress
FROM SNMPv2-SMI
RowStatus, TruthValue, TEXTUAL-CONVENTION, PhysAddress
FROM SNMPv2-TC
Anderson et al. Expires January 2001 [Page 3]
Internet Draft IP Forwarding PIB July 2000
InetAddress
FROM INET-ADDRESS-MIB;
partition MODULE-IDENTITY
LAST-UPDATED "2302010000Z"
ORGANIZATION "Multiservice Switching Forum"
CONTACT-INFO "
Todd A. Anderson
Intel
2111 NE 25th Avenue
Hillsboro, OR 97124 USA
Phone: +1 503 712 1760
Email: todd.a.anderson@intel.com
Avri Doria
Nortel Networks
600 Technology Park Drive
Billerica MA 01821
Phone: +1 401 663 5024
Email: avri@nortelnetworks.com
Jiang Yong
Telia Research AB
123 86 Farsta
Sweden
Phone: +46 (0) 8 713 81 25
Email: yong.b.jiang@telia.se
Jerry Sydir
CPlane Inc.
5150 El Camino Real Suite B-31
Los Altos, CA 94022
Phone: +1 650 938 8066 x102
Email: sydir@cplane.com
Balaji Srinivasan
CPlane Inc.
5150 El Camino Real Suite B-31
Los Altos, CA 94022
phone: +1 650 938 8066 x103
Email: balaji@cplane.com
"
DESCRIPTION
"The network element partitioning MIB."
::= { enterprises 2000 }
msf OBJECT IDENTIFIER ::= { enterprises 2000 }
switchConfig OBJECT IDENTIFIER ::= { msf 1 }
vSwitchConfig OBJECT IDENTIFIER ::= { msf 2 }
PortDirection ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
Anderson et al. Expires January 2001 [Page 4]
Internet Draft IP Forwarding PIB July 2000
"The following type is used to specify the direction of the
label ranges and the bandwidth in the physical port of the switch
as well as the virtual port of the virtual switch."
SYNTAX INTEGER {
incoming(1),
outgoing(2)
}
OwnerString ::= TEXTUAL-CONVENTION
DISPLAY-HINT "255a"
STATUS current
DESCRIPTION
"This data type is used to model an administratively
assigned name of the owner of a resource. It is
suggested that this name contain one or more of
the following: manager station's transport address,
management station name (e.g., domain name), network
management personnel's name, location, or phone number.
In some cases the agent itself will be the owner of an
entry. In these cases, this string shall be set to a
string starting with 'agent'.
To facilitate internationalization, this information
is represented using the ISO/IEC IS 10646-1 character
set, encoded as an octet string using the UTF-8
transformation format described in [RFC2279].
Since additional code points are added by amendments
to the 10646 standard from time to time, implementations
must be prepared to encounter any code point from
0x00000000 to 0x7fffffff. Byte sequences that do not
correspond to the valid UTF-8 encoding of a code point
or are outside this range are prohibited. The use of
control codes should be avoided. When it is necessary
to represent a newline, the control code sequence CR LF
should be used. For code points not directly supported
by user interface hardware or software, an alternative
means of entry and display, such as hexadecimal, may be
provided. For information encoded in 7-bit US-ASCII,
the UTF-8 encoding is identical to the US-ASCII encoding.
UTF-8 may require multiple bytes to represent a single
character / code point; thus the length of this object
in octets may be different from the number of characters
encoded. Similarly, size constraints refer to the number
of encoded octets, not the number of characters represented
by an encoding. When this TC is used for an object that
is used or envisioned to be used as an index, then a SIZE
restriction MUST be specified so that the number of
sub-identifiers for any object instance does not exceed
the limit of 128, as defined by [RFC1905]."
SYNTAX OCTET STRING (SIZE(0..255))
RatioString ::= TEXTUAL-CONVENTION
Anderson et al. Expires January 2001 [Page 5]
Internet Draft IP Forwarding PIB July 2000
STATUS current
DESCRIPTION
"This data type is used to model a floating number,
specifically here the cell loss ratio and a probability
number. It is required to be of the form m:n, where m and
n are both integers and represent a floating number m
divided by n."
SYNTAX OCTET STRING (SIZE(3))
VectorString ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This data type is used to model a 2-dimentional number
(x,y). Here it is used to specify the vpi/vci range for an
ATM interface. 2 vectors, (minVpi, minVci) and (maxVpi,
maxVci), make up a label range. It is required to have the
format x:y"
SYNTAX OCTET STRING (SIZE(3..8))
-- ===============================================
-- Switch Resource configuration at startup time
-- The resource values when the system started
-- ===============================================
numRoutingEntries OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION " The number of routing table entries of this switch.
This value is ignored if the switch has only per port
routing tables (i.e., no switch-wide routing table)"
::= { switchConfig 1 }
switchPortConfigNumPorts OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Number of ports in this switch"
::= { switchConfig 2 }
switchPortConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF SwitchPortConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Resource configuration for each port on the switch"
::= { switchConfig 3 }
switchPortConfigEntry OBJECT-TYPE
SYNTAX SwitchPortConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table gives the resources configured for the
Anderson et al. Expires January 2001 [Page 6]
Internet Draft IP Forwarding PIB July 2000
various ports at the switch level"
INDEX { switchPortConfigPortID }
::= { switchPortConfigTable 1 }
SwitchPortConfigEntry ::= SEQUENCE {
switchPortConfigPortID Integer32,
switchPortConfigPortLabelType INTEGER,
switchPortConfigNumBWs INTEGER,
switchPortConfigNumLabelRanges INTEGER,
switchNumRoutingEntries INTEGER,
switchPortAllowsSci TruthValue
}
switchPortConfigPortID OBJECT-TYPE
SYNTAX Integer32 (1..65536)
MAX-ACCESS read-only
STATUS current
DESCRIPTION "This is the physical port id"
::= { switchPortConfigEntry 1 }
switchPortConfigPortLabelType OBJECT-TYPE
SYNTAX INTEGER {
atm(1),
frame-relay(2),
vlan(3),
mpls(4),
ip(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Indicates the type of protocol for labels at this
port."
::={ switchPortConfigEntry 2 }
switchPortConfigNumBWs OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Number of equivalent bandwidths for this port in the
incoming and outgoing directions."
::= { switchPortConfigEntry 3 }
switchPortConfigNumLabelRanges OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Number of label ranges for this port."
::= { switchPortConfigEntry 4 }
switchNumRoutingEntries OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
Anderson et al. Expires January 2001 [Page 7]
Internet Draft IP Forwarding PIB July 2000
DESCRIPTION "Number of routing entries for this port."
::= { switchPortConfigEntry 5 }
switchPortAllowsSci OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Indicates whether this port can be used to connect to
the SCI."
::= { switchPortConfigEntry 6 }
--==============================
-- END OF switchPortConfigTable
--==============================
--===============================================================
-- This table performanceParamTable is used to represent the
-- performance targets associated with the equivalent bandwidths for
-- each port. As referenced from MSF 99.208, this table allows the
-- bandwidth, buffer space, and queue schedulers assigned to a VS to be
-- simply abstracted using a single parameter: the Equivalent bandwidth
-- per port assigned to the VS. Each entry in the interface bandwidth
-- table (either for a VS or for the physical switch) uses its
-- ServiceParamIndex to point to a row in this table. Then the
-- equivalent bandwidth points to a performance target set by the
-- service descriptor parameters. The performance target is most common
-- in the form of a loss target but also a delay target can be used.
--===============================================================
performanceParamTable OBJECT-TYPE
SYNTAX SEQUENCE OF PerformanceParamEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Table giving the configured performance targets for
this switch"
::={ switchConfig 4 }
performanceParamEntry OBJECT-TYPE
SYNTAX PerformanceParamEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table entry gives each performance target
parameters"
INDEX { performanceParamIndex }
::= { performanceParamTable 1 }
PerformanceParamEntry ::=
SEQUENCE {
performanceParamIndex Integer32,
performancePLR RatioString,
performanceMaxDelay INTEGER,
performanceDelayOverProb RatioString
Anderson et al. Expires January 2001 [Page 8]
Internet Draft IP Forwarding PIB July 2000
}
performanceParamIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Identifies each performance target"
::= { performanceParamEntry 1 }
performancePLR OBJECT-TYPE
SYNTAX RatioString
MAX-ACCESS read-only
STATUS current
DESCRIPTION "This indicates the packet loss ratio "
::= { performanceParamEntry 2 }
performanceMaxDelay OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION " This indicates the maximum packet delay "
::= { performanceParamEntry 3 }
performanceDelayOverProb OBJECT-TYPE
SYNTAX RatioString
MAX-ACCESS read-only
STATUS current
DESCRIPTION " This indicates the possibility that the packet delay
is bigger than the maximum delay allowed "
::= { performanceParamEntry 4 }
--===================================
--End of performanceParamTable
--===================================
--===============================================================
-- The table switchPortConfigBWTable is used to give the equivalent
-- bandwidths associated with different performance targets at the
-- switch level. The object, performanceParamIndex, will point to an
-- entry in the table performanceParamTable. This gives the
-- performance target for the equivalent bandwidth of this interface.
-- This table is indexed by the port number, and the bandwidth ID.
--===============================================================
switchPortConfigBWTable OBJECT-TYPE
SYNTAX SEQUENCE OF SwitchPortConfigBWEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Table giving the configured equivalent bandwidths
for the various switch ports"
::= { switchConfig 5 }
switchPortConfigBWEntry OBJECT-TYPE
Anderson et al. Expires January 2001 [Page 9]
Internet Draft IP Forwarding PIB July 2000
SYNTAX SwitchPortConfigBWEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table gives the per port equivalent bandwidths"
INDEX { switchPortConfigBWPortID,
switchPortConfigBWID }
::= { switchPortConfigBWTable 1 }
SwitchPortConfigBWEntry ::=
SEQUENCE {
switchPortConfigBWPortID Integer32,
switchPortConfigBWID Integer32,
switchPortConfigEqiBW INTEGER,
switchPortPerformanceIndex INTEGER,
switchPortConfigBWPortDirection PortDirection
}
switchPortConfigBWPortID OBJECT-TYPE
SYNTAX Integer32 (1..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Identifies the switch port number"
::= { switchPortConfigBWEntry 1 }
switchPortConfigBWID OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "This is the equivalent bandwidth ID in the switch"
::= { switchPortConfigBWEntry 2 }
switchPortConfigEqiBW OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Indicates the equivalent bandwidth for this port."
::= { switchPortConfigBWEntry 3 }
switchPortPerformanceIndex OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Indicates an entry in the performanceParamTable which
represents the performance target associated with this
equivalent bandwidth"
::= { switchPortConfigBWEntry 4 }
switchPortConfigBWPortDirection OBJECT-TYPE
SYNTAX PortDirection
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Indicates the direction for which this equivalent
bandwidth is valid"
Anderson et al. Expires January 2001 [Page 10]
Internet Draft IP Forwarding PIB July 2000
::= { switchPortConfigBWEntry 5 }
--===================================
--End of switchPortConfigBWTable
--===================================
--===============================================================
-- The table switchPortConfigLabelRangeTable is used to give the label
-- ranges at the switch level. As different interfaces may have
-- different service types, what kind of label identity is used will
-- depend on the interface service type. An ATM interface should have
-- VPI/VCI ranges. A Frame Relay interface should have DLCI ranges. A
-- MPLS interface should have MPLS label ID ranges. An VLAN-aware
-- Ethernet switch should have VLAN ID ranges. An IP router should have
-- IP address ranges. The table index is the port number and the label
-- range ID.
--===============================================================
switchPortConfigLabelRangeTable OBJECT-TYPE
SYNTAX SEQUENCE OF SwitchPortConfigLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Table giving the configured label range information
for the various switch ports"
::= { switchConfig 6 }
switchPortConfigLabelRangeEntry OBJECT-TYPE
SYNTAX SwitchPortConfigLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table gives the per port label ranges"
INDEX { switchPortConfigLabelRangePortID,
switchPortConfigLabelRangeID }
::= { switchPortConfigLabelRangeTable 1 }
SwitchPortConfigLabelRangeEntry ::=
SEQUENCE {
switchPortConfigLabelRangePortID Integer32,
switchPortConfigLabelRangeID Integer32,
switchPortConfigLabelRangePortDirection PortDirection,
switchPortConfigLabelRangeIndex INTEGER
}
switchPortConfigLabelRangePortID OBJECT-TYPE
SYNTAX Integer32 (1..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Identifies the port to which this range belongs"
::= { switchPortConfigLabelRangeEntry 1 }
switchPortConfigLabelRangeID OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
Anderson et al. Expires January 2001 [Page 11]
Internet Draft IP Forwarding PIB July 2000
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Identifies a certain label range for the port. For any
port, its label ranges are sequentially numbered from 1
to switchPortConfigNumLabelRanges defined in
switchPortConfigEntry"
::= { switchPortConfigLabelRangeEntry 2 }
switchPortConfigLabelRangePortDirection OBJECT-TYPE
SYNTAX PortDirection
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Indicates the direction for which this range is valid"
::= { switchPortConfigLabelRangeEntry 3 }
switchPortConfigLabelRangeIndex OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The index into the protocol-dependent label range
table."
::= { switchPortConfigLabelRangeEntry 4 }
--====================================
-- END OF switchPortConfigLabelRangeTable
--====================================
--===============================================================
-- The table atmLabelRangeTable is used to give the VPI/VCI label
ranges
-- at the ATM switch level.
--===============================================================
atmLabelRangeTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Table giving the configured ATM label range
information for the various switch ports"
::= { switchConfig 7 }
atmLabelRangeEntry OBJECT-TYPE
SYNTAX AtmLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table gives the per port ATM label ranges and
capabilities."
INDEX { atmLabelRangeIndex }
::= { atmLabelRangeTable 1 }
AtmLabelRangeEntry ::=
SEQUENCE {
atmLabelRangeIndex Integer32,
Anderson et al. Expires January 2001 [Page 12]
Internet Draft IP Forwarding PIB July 2000
atmLabelRangeMinVpiVci VectorString,
atmLabelRangeMaxVpiVci VectorString,
atmLabelRangeAllowsVP TruthValue,
atmLabelRangeAllowsP2MP TruthValue,
atmLabelRangeAllowsMP2P TruthValue,
atmLabelRangeMaxMulticast INTEGER
}
atmLabelRangeIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Index into this table."
::= { atmLabelRangeEntry 1 }
atmLabelRangeMinVpiVci OBJECT-TYPE
SYNTAX VectorString
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Lower bound of the vpi and vci range."
::= { atmLabelRangeEntry 2 }
atmLabelRangeMaxVpiVci OBJECT-TYPE
SYNTAX VectorString
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Upper bound of the vpi and vci range."
::= { atmLabelRangeEntry 3 }
atmLabelRangeAllowsVP OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Indicates whether this label range can be used for VP
connections."
::= { atmLabelRangeEntry 4 }
atmLabelRangeAllowsP2MP OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Indicates whether this label range can be used to
create point-to-multipoint connections."
::= { atmLabelRangeEntry 5 }
atmLabelRangeAllowsMP2P OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Indicates whether this label range can be used to
create multipoint-to-point connections."
::= { atmLabelRangeEntry 6 }
Anderson et al. Expires January 2001 [Page 13]
Internet Draft IP Forwarding PIB July 2000
atmLabelRangeMaxMulticast OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Indicates the maximum number of multicast connections
that can be created within this range."
::= { atmLabelRangeEntry 7 }
--====================================
-- END OF atmLabelRangeTable
--====================================
--===============================================================
-- The table frLabelRangeTable is used to give the DLCI label ranges
-- on a Frame Relay interface.
--===============================================================
frLabelRangeTable OBJECT-TYPE
SYNTAX SEQUENCE OF FrLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Table giving the configured label range information
for the various frame relay ports."
::= { switchConfig 8 }
frLabelRangeEntry OBJECT-TYPE
SYNTAX FrLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table gives the per port label ranges"
INDEX { frLabelRangeIndex }
::= { frLabelRangeTable 1 }
FrLabelRangeEntry ::=
SEQUENCE {
frLabelRangeIndex Integer32,
frLabelRangeMinDLCI INTEGER,
frLabelRangeMaxDLCI INTEGER
}
frLabelRangeIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Index into this table."
::= { frLabelRangeEntry 1 }
frLabelRangeMinDLCI OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Lower bound of the DLCI range for this Frame Relay
Anderson et al. Expires January 2001 [Page 14]
Internet Draft IP Forwarding PIB July 2000
interface."
::= { frLabelRangeEntry 2 }
frLabelRangeMaxDLCI OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Upper bound of the DLCI range for this Frame Relay
interface."
::= { frLabelRangeEntry 3 }
--====================================
-- END OF frLabelRangeTable
--====================================
--===============================================================
-- The table vlanLabelRangeTable is used to give the VLAN ID label
ranges
-- on a VLAN-aware Ethernet interface.
--===============================================================
vlanLabelRangeTable OBJECT-TYPE
SYNTAX SEQUENCE OF VlanLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Table giving the configured label range information
for the VLAN-aware Ethernet ports."
::= { switchConfig 9 }
vlanLabelRangeEntry OBJECT-TYPE
SYNTAX VlanLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table gives the per port VLAN ID ranges"
INDEX { vlanLabelRangeIndex }
::= { vlanLabelRangeTable 1 }
VlanLabelRangeEntry ::=
SEQUENCE {
vlanLabelRangeIndex Integer32,
vlanLabelRangeMinID INTEGER,
vlanLabelRangeMaxID INTEGER
}
vlanLabelRangeIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Index into this table."
::= { vlanLabelRangeEntry 1 }
vlanLabelRangeMinID OBJECT-TYPE
SYNTAX INTEGER
Anderson et al. Expires January 2001 [Page 15]
Internet Draft IP Forwarding PIB July 2000
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Lower bound of the VLAN ID range on this VLAN-aware
Ethernet switch interface."
::= { vlanLabelRangeEntry 2 }
vlanLabelRangeMaxID OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Upper bound of the VLAN ID range on this VLAN-aware
Ethernet switch interface."
::= { vlanLabelRangeEntry 3 }
--====================================
-- END OF vlanLabelRangeTable
--====================================
--===============================================================
-- The table mplsLabelRangeTable is used to give the label ranges
-- on a MPLS interface.
--===============================================================
mplsLabelRangeTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Table giving the configured label range information
for MPLS ports."
::= { switchConfig 10 }
mplsLabelRangeEntry OBJECT-TYPE
SYNTAX MplsLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table gives the per port MPLS ranges."
INDEX { mplsLabelRangeIndex }
::= { mplsLabelRangeTable 1 }
MplsLabelRangeEntry ::=
SEQUENCE {
mplsLabelRangeIndex Integer32,
mplsLabelRangeMinID INTEGER,
mplsLabelRangeMaxID INTEGER
}
mplsLabelRangeIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Index into this table."
::= { mplsLabelRangeEntry 1 }
Anderson et al. Expires January 2001 [Page 16]
Internet Draft IP Forwarding PIB July 2000
mplsLabelRangeMinID OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Lower bound of the MPLS label range."
::= { mplsLabelRangeEntry 2 }
mplsLabelRangeMaxID OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Upper bound of the MPLS label range."
::= { mplsLabelRangeEntry 3 }
--====================================
-- END OF mplsLabelRangeTable
--====================================
--===============================================================
-- The table ipLabelRangeTable is used to give the IP ranges on an IP
-- interface.
--===============================================================
ipLabelRangeTable OBJECT-TYPE
SYNTAX SEQUENCE OF IpLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Table giving the configured IP ranges for IP ports."
::= { switchConfig 11 }
ipLabelRangeEntry OBJECT-TYPE
SYNTAX IpLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table gives the per port IP ranges."
INDEX { ipLabelRangeIndex }
::= { ipLabelRangeTable 1 }
IpLabelRangeEntry ::=
SEQUENCE {
ipLabelRangeIndex Integer32,
ipLabelRangeIP IpAddress,
ipLabelRangeIPMask IpAddress
}
ipLabelRangeIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Index into this table."
::= { ipLabelRangeEntry 1 }
Anderson et al. Expires January 2001 [Page 17]
Internet Draft IP Forwarding PIB July 2000
ipLabelRangeIP OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Indicates the IP address for a particular network."
::= { ipLabelRangeEntry 2 }
ipLabelRangeIPMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Indicates the subnet's mask address."
::= { ipLabelRangeEntry 3 }
--====================================
-- END OF ipLabelRangeTable
--====================================
numberOfVirtualSwitches OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The number of virtual switches that have been currently
configured on this switch"
::= { vSwitchConfig 1 }
vSwitchConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF VSwitchConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Each row in this table describes a virtual switch that
has been created on this switch"
::= { vSwitchConfig 2 }
vSwitchConfigEntry OBJECT-TYPE
SYNTAX VSwitchConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION " "
INDEX { vSwitchConfigVsID }
::= { vSwitchConfigTable 1 }
VSwitchConfigEntry ::= SEQUENCE {
vSwitchConfigVsID Integer32,
vSwitchAdminStatus INTEGER,
vSwitchOperStatus INTEGER,
vSwitchNumCtrls INTEGER,
vSwitchNumPorts INTEGER,
vSwitchNumSynPorts INTEGER,
vSwitchPortNumRoutingEntries INTEGER,
vSwitchTableOwner OwnerString,
vSwitchTableRowStatus RowStatus
Anderson et al. Expires January 2001 [Page 18]
Internet Draft IP Forwarding PIB July 2000
}
vSwitchConfigVsID OBJECT-TYPE
SYNTAX Integer32 (1..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Identifies the virtual switch within this switch"
::= { vSwitchConfigEntry 1 }
vSwitchAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2),
testing(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The administrative state of the virtual switch. A
virtual switch's administrative status can not be up
until all the necessary parameters for this virtual
switch have been specified"
::={ vSwitchConfigEntry 2 }
vSwitchOperStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The current operational state of the virtual switch"
::={ vSwitchConfigEntry 3 }
vSwitchNumCtrls OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The number of controllers for this virtual switch"
::= {vSwitchConfigEntry 4}
vSwitchNumPorts OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The number of virtual ports in this virtual switch"
::= {vSwitchConfigEntry 5 }
vSwitchNumSynPorts OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The number of synthetic ports in this virtual switch"
::= {vSwitchConfigEntry 6 }
Anderson et al. Expires January 2001 [Page 19]
Internet Draft IP Forwarding PIB July 2000
vSwitchPortNumRoutingEntries OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The number of routing table entries allocated to this
virtual port from the physical port. This value is
used only if the switch has per port routing tables"
::= { vSwitchConfigEntry 7 }
vSwitchTableOwner OBJECT-TYPE
SYNTAX OwnerString
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Standard owner string (rowstatus convention)"
::= { vSwitchConfigEntry 8 }
vSwitchTableRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Used in creating/deleting the row"
::= { vSwitchConfigEntry 9 }
--===============================
-- END OF vSwitchConfigTable
--===============================
vSwitchCtrlConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF VSwitchCtrlConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table gives the controllers configured for the VS"
::= {vSwitchConfig 3}
vSwitchCtrlConfigEntry OBJECT-TYPE
SYNTAX VSwitchCtrlConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Configuration for a controller for the VS"
INDEX { vSwitchCtrlVsID }
::= {vSwitchCtrlConfigTable 1}
VSwitchCtrlConfigEntry ::=
SEQUENCE {
vSwitchCtrlVsID Integer32,
vSwitchCtrlID INTEGER,
vSwitchSciType INTEGER,
vSwitchNumCurrentControllers INTEGER,
vSwitchCtrlConfigTableRowStatus RowStatus
}
vSwitchCtrlVsID OBJECT-TYPE
Anderson et al. Expires January 2001 [Page 20]
Internet Draft IP Forwarding PIB July 2000
SYNTAX Integer32 (1..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Identifies the virtual switch within this switch"
::= { vSwitchCtrlConfigEntry 1 }
vSwitchCtrlID OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Identifies the virtual switch controller across the
SCI"
::= { vSwitchCtrlConfigEntry 2 }
--=======================================
-- megaco and cops-pr could be added here
--=======================================
vSwitchSciType OBJECT-TYPE
SYNTAX INTEGER {
gsmp(1)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The switch control protocol used to control this
virtual switch"
::= { vSwitchCtrlConfigEntry 3 }
vSwitchNumCurrentControllers OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The number of controllers currently connected
to this VS"
::= { vSwitchCtrlConfigEntry 4 }
vSwitchCtrlConfigTableRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Used in creating/deleting the row"
::= { vSwitchCtrlConfigEntry 5 }
--===============================
--END OF vSwitchCtrlConfigTable
--===============================
--===============================================================
-- The table vSwitchCurCtrlsTable gives the Internet
-- addresses by which each of the current controllers for each
-- VS can be contacted.
--===============================================================
Anderson et al. Expires January 2001 [Page 21]
Internet Draft IP Forwarding PIB July 2000
vSwitchCurCtrlsTable OBJECT-TYPE
SYNTAX SEQUENCE OF VSwitchCurCtrlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Table giving the addresses of controllers
currently connected to a virtual switch."
::= { vSwitchConfig 7 }
vSwitchCurCtrlEntry OBJECT-TYPE
SYNTAX VSwitchCurCtrlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "The virtual switch and the address of one
of the currently connected controllers."
INDEX { vSwitchCurCtrlVS }
::= { vSwitchCurCtrlsTable 1 }
VSwitchCurCtrlEntry ::=
SEQUENCE {
vSwitchCurCtrlVS Integer32,
vSwitchCurCtrlAddr InetAddress,
vSwitchCurCtrlType INTEGER
}
vSwitchCurCtrlVS OBJECT-TYPE
SYNTAX Integer32 (1..65536)
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Identifies the virtual switch within this switch"
::= { vSwitchCurCtrlEntry 1 }
vSwitchCurCtrlAddr OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The Internet address by which this controller can
be contacted"
::= { vSwitchCurCtrlEntry 2 }
vSwitchCurCtrlType OBJECT-TYPE
SYNTAX INTEGER {
gsmp(1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION "The type of connected controller"
::= { vSwitchCurCtrlEntry 3 }
--===============================
--END OF vSwitchCurCtrlsTable
--===============================
Anderson et al. Expires January 2001 [Page 22]
Internet Draft IP Forwarding PIB July 2000
--===============================================================
-- The table vSwitchEthernetCtrlTable gives the source MAC
-- address of the controller used to control a virtual switch.
--===============================================================
vSwitchEthernetCtrlTable OBJECT-TYPE
SYNTAX SEQUENCE OF VSwitchEthernetCtrlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Table giving the source MAC of the controller for this
virtual switch."
::= { vSwitchConfig 4 }
vSwitchEthernetCtrlEntry OBJECT-TYPE
SYNTAX VSwitchEthernetCtrlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Table giving the source MAC of the controller for this
virtual switch."
INDEX { vSwitchEthernetConfigVsID,
vSwitchEthernetCtrlID }
::= { vSwitchEthernetCtrlTable 1 }
VSwitchEthernetCtrlEntry ::=
SEQUENCE {
vSwitchEthernetConfigVsID Integer32,
vSwitchEthernetCtrlID Integer32,
vSwitchEthernetCtrlSourceMAC PhysAddress
}
vSwitchEthernetConfigVsID OBJECT-TYPE
SYNTAX Integer32 (1..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Identifies the virtual switch within this switch"
::= { vSwitchEthernetCtrlEntry 1 }
vSwitchEthernetCtrlID OBJECT-TYPE
SYNTAX Integer32 (1..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Identifies the virtual switch controller across the
SCI"
::= { vSwitchEthernetCtrlEntry 2 }
vSwitchEthernetCtrlSourceMAC OBJECT-TYPE
SYNTAX PhysAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The source MAC to be used for the controller of this
virtual switch."
::= { vSwitchEthernetCtrlEntry 3 }
Anderson et al. Expires January 2001 [Page 23]
Internet Draft IP Forwarding PIB July 2000
--===============================
--END OF vSwitchEthernetCtrlTable
--===============================
--===============================================================
-- The table vSwitchAtmCtrlTable gives the VPI/VCI labels used by
-- a control protocol to access the virtual switch.
--===============================================================
vSwitchAtmCtrlTable OBJECT-TYPE
SYNTAX SEQUENCE OF VSwitchAtmCtrlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Table giving the VPI/VCI used by a protocol to control
a virtual switch."
::= { vSwitchConfig 5 }
vSwitchAtmCtrlEntry OBJECT-TYPE
SYNTAX VSwitchAtmCtrlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Table giving the VPI/VCI used by a protocol to control
a virtual switch."
INDEX { vSwitchAtmCtrlLabelIndex }
::= { vSwitchAtmCtrlTable 1 }
VSwitchAtmCtrlEntry ::=
SEQUENCE {
vSwitchAtmCtrlLabelIndex Integer32,
vSwitchAtmCtrlID INTEGER,
vSwitchAtmCtrlLabelVpi INTEGER,
vSwitchAtmCtrlLabelVci INTEGER
}
vSwitchAtmCtrlLabelIndex OBJECT-TYPE
SYNTAX Integer32 (1..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Identifies the virtual switch within this switch"
::= { vSwitchAtmCtrlEntry 1 }
vSwitchAtmCtrlID OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Identifies the virtual switch controller across the
SCI"
::= { vSwitchAtmCtrlEntry 2 }
vSwitchAtmCtrlLabelVpi OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-write
Anderson et al. Expires January 2001 [Page 24]
Internet Draft IP Forwarding PIB July 2000
STATUS current
DESCRIPTION "The VPI on which the control messages are exchanged."
::= { vSwitchAtmCtrlEntry 3 }
vSwitchAtmCtrlLabelVci OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The VCI on which the control messages are exchanged."
::= { vSwitchAtmCtrlEntry 4 }
--===============================
--END OF vSwitchAtmCtrlTable
--===============================
--===============================================================
-- The table vSwitchTcpCtrlTable gives the TCP port number used by
-- a control protocol to access the virtual switch.
--===============================================================
vSwitchTcpCtrlTable OBJECT-TYPE
SYNTAX SEQUENCE OF VSwitchTcpCtrlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Table giving the TCP port number used by a protocol to
control a virtual switch."
::= { vSwitchConfig 6 }
vSwitchTcpCtrlEntry OBJECT-TYPE
SYNTAX VSwitchTcpCtrlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Table giving the TCP port number used by a protocol to
control a virtual switch."
INDEX { vSwitchTcpCtrlPortIndex }
::= { vSwitchTcpCtrlTable 1 }
VSwitchTcpCtrlEntry ::=
SEQUENCE {
vSwitchTcpCtrlPortIndex Integer32,
vSwitchTcpCtrlID INTEGER,
vSwitchTcpCtrlPortNumber INTEGER,
vSwitchTcpCtrlSourceIP IpAddress,
vSwitchTcpCtrlSourceNetmask IpAddress
}
vSwitchTcpCtrlPortIndex OBJECT-TYPE
SYNTAX Integer32 (1..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Identifies the virtual switch within this switch"
::= { vSwitchTcpCtrlEntry 1 }
Anderson et al. Expires January 2001 [Page 25]
Internet Draft IP Forwarding PIB July 2000
vSwitchTcpCtrlID OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Identifies the virtual switch controller across the
SCI"
::= { vSwitchTcpCtrlEntry 2 }
vSwitchTcpCtrlPortNumber OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The local port number used to control the virtual
switch."
::= { vSwitchTcpCtrlEntry 3 }
vSwitchTcpCtrlSourceIP OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The source subnet or specific IP address from which the
controller of the virtual switch must originate."
::= { vSwitchTcpCtrlEntry 3 }
vSwitchTcpCtrlSourceNetmask OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The source subnet mask (255.255.255.255 to specify a
specific IP address) from which the controller of the
virtual switch must originate."
::= { vSwitchTcpCtrlEntry 4 }
--===============================
--END OF vSwitchTcpCtrlTable
--===============================
--===============================
--vSwitchPortConfigTable. These are
--only for non-synthetic virtual ports
--===============================
vSwitchPortConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF VSwitchPortConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Resource configuration for the virtual ports"
::= { vSwitchConfig 8 }
vSwitchPortConfigEntry OBJECT-TYPE
SYNTAX VSwitchPortConfigEntry
MAX-ACCESS not-accessible
Anderson et al. Expires January 2001 [Page 26]
Internet Draft IP Forwarding PIB July 2000
STATUS current
DESCRIPTION "This table gives the per port resource configured for
the virtual switch. The vSwitchPortConfigVSID and
vSwitchVirtualPortID combination must be unique between
this table and vSwitchCrossVSTable."
INDEX { vSwitchPortConfigVSID, vSwitchVirtualPortID }
::= { vSwitchPortConfigTable 1 }
VSwitchPortConfigEntry ::=
SEQUENCE {
vSwitchPortConfigVSID Integer32,
vSwitchVirtualPortID Integer32,
vSwitchPhysicalPortNumber INTEGER,
vSwitchPortConfigPortNumBWs INTEGER,
vSwitchPortConfigNumLabelRanges INTEGER,
vSwitchPortConfigRowStatus RowStatus
}
vSwitchPortConfigVSID OBJECT-TYPE
SYNTAX Integer32 (1..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "This is the virtual switch ID of the virtual switch"
::= { vSwitchPortConfigEntry 1 }
vSwitchVirtualPortID OBJECT-TYPE
SYNTAX Integer32 (1..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "This is the virtual port id in that virtual switch"
::= { vSwitchPortConfigEntry 2 }
vSwitchPhysicalPortNumber OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The physical port number that is mapped to virtual
port"
::= { vSwitchPortConfigEntry 3 }
vSwitchPortConfigPortNumBWs OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Number of equivalent bandwidth pointing to different
performance targets (packet loss ratio and delay)in both
incoming and outgoing directions for this port."
::= { vSwitchPortConfigEntry 4 }
vSwitchPortConfigNumLabelRanges OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
Anderson et al. Expires January 2001 [Page 27]
Internet Draft IP Forwarding PIB July 2000
DESCRIPTION "Number of label ranges for this port. The label can be
of different types depending on the interface service
type."
::= { vSwitchPortConfigEntry 5 }
vSwitchPortConfigRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Used in creating/deleting the row"
::= { vSwitchPortConfigEntry 5 }
--================================
-- END OF vSwitchPortConfigTable
--================================
--===============================================================
-- The table vSwitchConfigBWTable gives the equivalent bandwidth
-- pointing to different service category for input and output at the
-- virtual ports. The table has 3 indices; virtual switch ID, port ID
-- and Bandwidth ID.
--===============================================================
vSwitchPortConfigBWTable OBJECT-TYPE
SYNTAX SEQUENCE OF VSwitchPortConfigBWEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Table giving the configured bandwidth information
for the various virtual ports"
::= { vSwitchConfig 9 }
vSwitchPortConfigBWEntry OBJECT-TYPE
SYNTAX VSwitchPortConfigBWEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table gives the configured bandwidth information
for the various virtual ports"
INDEX { vSwitchBWConfigVSID,
vSwitchBWVirtualPortID,
vSwitchPortConfigBWID }
::= { vSwitchPortConfigBWTable 1 }
VSwitchPortConfigBWEntry ::=
SEQUENCE {
vSwitchBWConfigVSID Integer32,
vSwitchBWVirtualPortID Integer32,
vSwitchPortConfigBWID Integer32,
vSwitchPortConfigEqiBW INTEGER,
vSwitchBWPerformanceIndex INTEGER,
vSwitchPortConfigBWPortDirection PortDirection,
vSwitchPortConfigBWRowStatus RowStatus
}
Anderson et al. Expires January 2001 [Page 28]
Internet Draft IP Forwarding PIB July 2000
vSwitchBWConfigVSID OBJECT-TYPE
SYNTAX Integer32 (1..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "This is the virtual switch ID of the virtual switch"
::= { vSwitchPortConfigBWEntry 1 }
vSwitchBWVirtualPortID OBJECT-TYPE
SYNTAX Integer32 (1..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "This is the virtual port id in the current virtual
switch"
::= { vSwitchPortConfigBWEntry 2 }
vSwitchPortConfigBWID OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "This is the equivalent bandwidth ID in the current
virtual switch"
::= { vSwitchPortConfigBWEntry 3 }
vSwitchPortConfigEqiBW OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Indicates the equivalent bandwidth assigned
to this VS "
::= { vSwitchPortConfigBWEntry 4 }
vSwitchBWPerformanceIndex OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Indicates an entry in the performanceParamTable which
represents the performance target associated to by this
equivalent bandwidth "
::= { vSwitchPortConfigBWEntry 5 }
vSwitchPortConfigBWPortDirection OBJECT-TYPE
SYNTAX PortDirection
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Indicates the direction for which this equivalent
bandwidth is valid"
::= { vSwitchPortConfigBWEntry 6 }
vSwitchPortConfigBWRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Used in creation/deletion of the row"
Anderson et al. Expires January 2001 [Page 29]
Internet Draft IP Forwarding PIB July 2000
::= { vSwitchPortConfigBWEntry 7 }
--==================================
-- END OF vSwitchPortConfigBWTable
--==================================
--===============================================================
-- The vSwitchLabelRangeConfigTable gives the label ranges for input
and output
-- at the virtual ports.
-- The tables have 3 indices; virtual switch ID, port ID and Range ID
--===============================================================
vSwitchPortConfigLabelRangeTable OBJECT-TYPE
SYNTAX SEQUENCE OF VSwitchPortConfigLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Table giving the configured label range information
for the various virtual ports"
::= { vSwitchConfig 10 }
vSwitchPortConfigLabelRangeEntry OBJECT-TYPE
SYNTAX VSwitchPortConfigLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table gives the per port label ranges configured
for the virtual switch."
INDEX { vSwitchLRTConfigVSID,
vSwitchLRTVirtualPortID,
vSwitchPortConfigLabelRangeID }
::= { vSwitchPortConfigLabelRangeTable 1 }
VSwitchPortConfigLabelRangeEntry ::=
SEQUENCE {
vSwitchLRTConfigVSID Integer32,
vSwitchLRTVirtualPortID Integer32,
vSwitchPortConfigLabelRangeID Integer32,
vSwitchPortConfigPortDirection PortDirection,
vSwitchPortConfigLabelRangeType INTEGER,
vSwitchPortConfigLabelRangeIndex INTEGER,
vSwitchPortConfigLabelRowStatus RowStatus
}
vSwitchLRTConfigVSID OBJECT-TYPE
SYNTAX Integer32 (1..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "This is the virtual switch ID of the virtual switch"
::= { vSwitchPortConfigLabelRangeEntry 1 }
vSwitchLRTVirtualPortID OBJECT-TYPE
SYNTAX Integer32 (1..65536)
Anderson et al. Expires January 2001 [Page 30]
Internet Draft IP Forwarding PIB July 2000
MAX-ACCESS read-write
STATUS current
DESCRIPTION "This is the virtual port id in the current virtual
switch"
::= { vSwitchPortConfigLabelRangeEntry 2 }
vSwitchPortConfigLabelRangeID OBJECT-TYPE
SYNTAX Integer32 (1..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Identifies the label range"
::= { vSwitchPortConfigLabelRangeEntry 3 }
vSwitchPortConfigPortDirection OBJECT-TYPE
SYNTAX PortDirection
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Indicates the direction for which this range is valid"
::= { vSwitchPortConfigLabelRangeEntry 4 }
vSwitchPortConfigLabelRangeType OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Indicates the type of protocol for this label range."
::= { vSwitchPortConfigLabelRangeEntry 5 }
vSwitchPortConfigLabelRangeIndex OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-write
STATUS current
DESCRIPTION "The index into the protocol-dependent label
range table for this virtual switch."
::= { vSwitchPortConfigLabelRangeEntry 6 }
vSwitchPortConfigLabelRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Used in creation/deletion of row."
::= { vSwitchPortConfigLabelRangeEntry 7 }
--====================================
-- END OF vSwitchPortConfigLabelRangeTable
--====================================
--===============================================================
-- The table vsAtmLabelRangeTable is used to give the VPI/VCI label
ranges
-- at the ATM virtual switch level.
--===============================================================
vsAtmLabelRangeTable OBJECT-TYPE
Anderson et al. Expires January 2001 [Page 31]
Internet Draft IP Forwarding PIB July 2000
SYNTAX SEQUENCE OF VsAtmLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Table giving the configured ATM label range information
for the various switch ports on this virtual switch."
::= { vSwitchConfig 11 }
vsAtmLabelRangeEntry OBJECT-TYPE
SYNTAX VsAtmLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table gives the per port ATM label ranges and
capabilities."
INDEX { vsAtmLabelRangeIndex }
::= { vsAtmLabelRangeTable 1 }
VsAtmLabelRangeEntry ::=
SEQUENCE {
vsAtmLabelRangeIndex Integer32,
vsAtmLabelRangeMinVpiVci VectorString,
vsAtmLabelRangeMaxVpiVci VectorString,
vsAtmLabelRangeAllowsVP TruthValue,
vsAtmLabelRangeAllowsP2MP TruthValue,
vsAtmLabelRangeAllowsMP2P TruthValue,
vsAtmLabelRangeMaxMulticast INTEGER,
vsAtmLabelRangeRowStatus RowStatus
}
vsAtmLabelRangeIndex OBJECT-TYPE
SYNTAX Integer32 (1..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Index into this table."
::= { vsAtmLabelRangeEntry 1 }
vsAtmLabelRangeMinVpiVci OBJECT-TYPE
SYNTAX VectorString
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Lower bound of the vpi and vci range."
::= { vsAtmLabelRangeEntry 2 }
vsAtmLabelRangeMaxVpiVci OBJECT-TYPE
SYNTAX VectorString
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Upper bound of the vpi and vci range."
::= { vsAtmLabelRangeEntry 3 }
vsAtmLabelRangeAllowsVP OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
Anderson et al. Expires January 2001 [Page 32]
Internet Draft IP Forwarding PIB July 2000
DESCRIPTION "Indicates whether this label range can be used for VP
connections."
::= { vsAtmLabelRangeEntry 4 }
vsAtmLabelRangeAllowsP2MP OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Indicates whether this label range can be used to
create point-to-multipoint connections."
::= { vsAtmLabelRangeEntry 5 }
vsAtmLabelRangeAllowsMP2P OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Indicates whether this label range can be used to
create multipoint-to-point connections."
::= { vsAtmLabelRangeEntry 6 }
vsAtmLabelRangeMaxMulticast OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Indicates the maximum number of multicast connections
that can be created within this range."
::= { vsAtmLabelRangeEntry 7 }
vsAtmLabelRangeRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Indicates the maximum number of multicast connections
that can be created within this range."
::= { vsAtmLabelRangeEntry 8 }
--====================================
-- END OF vsAtmLabelRangeTable
--====================================
--===============================================================
-- The table vsFrLabelRangeTable is used to give the DLCI label ranges
-- on a Frame Relay interface for a virtual switch.
--===============================================================
vsFrLabelRangeTable OBJECT-TYPE
SYNTAX SEQUENCE OF VsFrLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Table giving the configured label range information
for the various frame relay ports."
::= { vSwitchConfig 12 }
Anderson et al. Expires January 2001 [Page 33]
Internet Draft IP Forwarding PIB July 2000
vsFrLabelRangeEntry OBJECT-TYPE
SYNTAX VsFrLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table gives the per port label ranges"
INDEX { vsFrLabelRangeIndex }
::= { vsFrLabelRangeTable 1 }
VsFrLabelRangeEntry ::=
SEQUENCE {
vsFrLabelRangeIndex Integer32,
vsFrLabelRangeMinDLCI INTEGER,
vsFrLabelRangeMaxDLCI INTEGER,
vsFrLabelRangeRowStatus RowStatus
}
vsFrLabelRangeIndex OBJECT-TYPE
SYNTAX Integer32 (1..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Index into this table."
::= { vsFrLabelRangeEntry 1 }
vsFrLabelRangeMinDLCI OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Lower bound of the DLCI range for this Frame Relay
interface."
::= { vsFrLabelRangeEntry 2 }
vsFrLabelRangeMaxDLCI OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Upper bound of the DLCI range for this Frame Relay
interface."
::= { vsFrLabelRangeEntry 3 }
vsFrLabelRangeRowStatus OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Used to create and delete this row."
::= { vsFrLabelRangeEntry 4 }
--====================================
-- END OF vsFrLabelRangeTable
--====================================
--===============================================================
Anderson et al. Expires January 2001 [Page 34]
Internet Draft IP Forwarding PIB July 2000
-- The table vsVlanLabelRangeTable is used to give the VLAN ID label
ranges
-- on a VLAN-aware Ethernet interface for a virtual switch.
--===============================================================
vsVlanLabelRangeTable OBJECT-TYPE
SYNTAX SEQUENCE OF VsVlanLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Table giving the configured label range information
for the VLAN-aware Ethernet ports."
::= { switchConfig 13 }
vsVlanLabelRangeEntry OBJECT-TYPE
SYNTAX VsVlanLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table gives the per port VLAN ID ranges"
INDEX { vsVlanLabelRangeIndex }
::= { vsVlanLabelRangeTable 1 }
VsVlanLabelRangeEntry ::=
SEQUENCE {
vsVlanLabelRangeIndex Integer32,
vsVlanLabelRangeMinID INTEGER,
vsVlanLabelRangeMaxID INTEGER,
vsVlanLabelRangeRowStatus RowStatus
}
vsVlanLabelRangeIndex OBJECT-TYPE
SYNTAX Integer32 (1..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Index into this table."
::= { vsVlanLabelRangeEntry 1 }
vsVlanLabelRangeMinID OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Lower bound of the VLAN ID range on this VLAN-aware
Ethernet switch interface."
::= { vsVlanLabelRangeEntry 2 }
vsVlanLabelRangeMaxID OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Upper bound of the VLAN ID range on this VLAN-aware
Ethernet switch interface."
::= { vsVlanLabelRangeEntry 3 }
vsVlanLabelRangeRowStatus OBJECT-TYPE
Anderson et al. Expires January 2001 [Page 35]
Internet Draft IP Forwarding PIB July 2000
SYNTAX RowStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Used to create and delete this row."
::= { vsVlanLabelRangeEntry 4 }
--====================================
-- END OF vsVlanLabelRangeTable
--====================================
--===============================================================
-- The table mplsLabelRangeTable is used to give the label ranges
-- on a MPLS interface.
--===============================================================
vsMplsLabelRangeTable OBJECT-TYPE
SYNTAX SEQUENCE OF VsMplsLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Table giving the configured label range information
for MPLS ports."
::= { vSwitchConfig 14 }
vsMplsLabelRangeEntry OBJECT-TYPE
SYNTAX VsMplsLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table gives the per port MPLS ranges."
INDEX { vsMplsLabelRangeIndex }
::= { vsMplsLabelRangeTable 1 }
VsMplsLabelRangeEntry ::=
SEQUENCE {
vsMplsLabelRangeIndex Integer32,
vsMplsLabelRangeMinID INTEGER,
vsMplsLabelRangeMaxID INTEGER,
vsMplsLabelRangeRowStatus RowStatus
}
vsMplsLabelRangeIndex OBJECT-TYPE
SYNTAX Integer32 (1..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Index into this table."
::= { vsMplsLabelRangeEntry 1 }
vsMplsLabelRangeMinID OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Lower bound of the MPLS label range."
::= { vsMplsLabelRangeEntry 2 }
Anderson et al. Expires January 2001 [Page 36]
Internet Draft IP Forwarding PIB July 2000
vsMplsLabelRangeMaxID OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Upper bound of the MPLS label range."
::= { vsMplsLabelRangeEntry 3 }
vsMplsLabelRangeRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Used to create or delete this row."
::= { vsMplsLabelRangeEntry 4 }
--====================================
-- END OF vsMplsLabelRangeTable
--====================================
--===============================================================
-- The table vsIpLabelRangeTable is used to give the IP ranges on an IP
-- interface for a virtual switch.
--===============================================================
vsIpLabelRangeTable OBJECT-TYPE
SYNTAX SEQUENCE OF VsIpLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "Table giving the configured IP ranges for IP ports."
::= { vSwitchConfig 15 }
vsIpLabelRangeEntry OBJECT-TYPE
SYNTAX VsIpLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table gives the per port IP ranges."
INDEX { vsIpLabelRangeIndex }
::= { vsIpLabelRangeTable 1 }
VsIpLabelRangeEntry ::=
SEQUENCE {
vsIpLabelRangeIndex Integer32,
vsIpLabelRangeIP IpAddress,
vsIpLabelRangeIPMask IpAddress,
vsIpLabelRangeRowStatus RowStatus
}
vsIpLabelRangeIndex OBJECT-TYPE
SYNTAX Integer32 (1..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Index into this table."
Anderson et al. Expires January 2001 [Page 37]
Internet Draft IP Forwarding PIB July 2000
::= { vsIpLabelRangeEntry 1 }
vsIpLabelRangeIP OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Indicates the IP address for a particular network."
::= { vsIpLabelRangeEntry 2 }
vsIpLabelRangeIPMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Indicates the subnet's mask address."
::= { vsIpLabelRangeEntry 3 }
vsIpLabelRangeRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Used for creating and deleting this row."
::= { vsIpLabelRangeEntry 4 }
--====================================
-- END OF vsIpLabelRangeTable
--====================================
--==========================================================
-- The vSwitchCrossVSTable contains rows that describe a
-- synthetic connection between two virtual switches. To each of
-- these switches, a synthetic port is added. This synthetic port
-- will appear as a real virtual port to the protocol managing the
-- virtual switch. As such, characteristics of the connection
-- have to be specified, e.g., link type (ATM, ethernet).
--
-- Some normal characteristics of a link do not need to be
-- specified because they can be computed dynamically by the switch.
-- For example, the bandwidth of the port can be computed as the
-- sum of the bandwidths of the other ports of the VS. This
-- bandwidth is necessary and sufficient to guarantee that the
-- synthetic port does not become an artificial bottleneck.
--==========================================================
vSwitchCrossVSTable OBJECT-TYPE
SYNTAX SEQUENCE OF VSwitchCrossVSEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "This table manages the virtual connection configured
between two VSs"
::= { vSwitchConfig 17 }
vSwitchCrossVSEntry OBJECT-TYPE
SYNTAX VSwitchCrossVSEntry
MAX-ACCESS not-accessible
Anderson et al. Expires January 2001 [Page 38]
Internet Draft IP Forwarding PIB July 2000
STATUS current
DESCRIPTION "Configuration for each virtual connection in the
switch"
INDEX { vSwitchVConnectID }
::= { vSwitchCrossVSTable 1}
VSwitchCrossVSEntry ::=
SEQUENCE {
vSwitchVConnectID Integer32,
vSwitchVConnect1VSID Integer32,
vSwitchVConnect1PortID Integer32,
vSwitchVConnect2VSID Integer32,
vSwitchVConnect2PortID Integer32,
vSwitchVLinkType INTEGER
}
vSwitchVConnectID OBJECT-TYPE
SYNTAX INTEGER (1..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Identifies this virtual connection"
::= { vSwitchCrossVSEntry 1 }
vSwitchVConnect1VSID OBJECT-TYPE
SYNTAX Integer32 (1..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "This is the virtual switch ID of the first virtual
switch attached to this synthetic connection."
::= { vSwitchCrossVSEntry 2 }
vSwitchVConnect1PortID OBJECT-TYPE
SYNTAX Integer32 (1..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "This is the virtual port id associated with this
synthetic connection in virtual switch
vSwitchVConnect1VSID."
::= { vSwitchCrossVSEntry 3 }
vSwitchVConnect2VSID OBJECT-TYPE
SYNTAX Integer32 (1..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "This is the virtual switch ID of the second virtual
switch attached to this synthetic connection."
::= { vSwitchCrossVSEntry 4 }
vSwitchVConnect2PortID OBJECT-TYPE
SYNTAX Integer32 (1..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION "This is the virtual port id associated with this
Anderson et al. Expires January 2001 [Page 39]
Internet Draft IP Forwarding PIB July 2000
synthetic connection in virtual switch
vSwitchVConnect2VSID."
::= { vSwitchCrossVSEntry 5 }
vSwitchVLinkType OBJECT-TYPE
SYNTAX INTEGER {
ethernet(1),
atm(2),
frame-relay(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION "Specifies the layer-2 link type that the virtual ports
associated with this synthetic connection will appear
to be."
::= { vSwitchCrossVSEntry 6 }
END
5. Security Considerations
Security issues are not addressed in this document.
6. Authors' Addresses
Todd A. Anderson
Intel
2111 NE 25th Avenue
Hillsboro, OR 97124 USA
Phone: +1 503 712 1760
Email: todd.a.anderson@intel.com
Avri Doria
Nortel Networks
600 Technology Park Drive
Billerica MA 01821
Phone: +1 401 663 5024
Email: avri@nortelnetworks.com
Jiang Yong
Telia Research AB
123 86 Farsta
Sweden
Phone: +46 (0) 8 713 81 25
Email: yong.b.jiang@telia.se
Jerry Sydir
CPlane Inc.
5150 El Camino Real Suite B-31
Los Altos, CA 94022
Phone: +1 650 938 8066 x102
Email: sydir@cplane.com
Anderson et al. Expires January 2001 [Page 40]
Internet Draft IP Forwarding PIB July 2000
Balaji Srinivasan
CPlane Inc.
5150 El Camino Real Suite B-31
Los Altos, CA 94022
phone: +1 650 938 8066 x103
Email: balaji@cplane.com
7. References
[MSF-VSMIB] T. Anderson, et. al., "Proposal for the Switch
Partitioning MIB", Multiservice Switching Forum 2001.008.
Anderson et al. Expires January 2001 [Page 41]
